TRANSTECTOR 1101-626 I2R ICP 48VDC
Comparison CITEL DS230S-48DC
Surge Protective Device (SPD)

CITEL DS230S-48DC Surge Protector	1101-626 I2R ICP 48VDC Surge Protector
Intended Application System
System Voltage	48VDC
Number of Phases	-
Conductors	2 Wire + Ground
Configuration	DC Power

PRODUCT COMPARISON TABLE

This page collects publicly available data from ul.com and assembles a side by side reference table for a convenient product cross reference.

Manufacturer		TRANSTECTOR
UL File #	E326289	E220064
Model	DS230S-48DC	1101-626 I2R ICP 48VDC
Product Image
UL.com Ratings	UL CARD	UL CARD
UL APPROVAL	Recognized UL 1449 5th Ed.	UL 1449 4th Ed. Recognized Isolated Loop Circuit Protector
UL MARK
SPD Type	4CA	UL497B
Volt (V)	48DC	48DC
AC/DC DC PV	DC	DC
Phase	n/a	n/a
Amps (A)	n/a	n/a
Ambient Min (C)	-40	-40
Ambient Max (C)	85	80
Mode
MLV (Vpk)
DC+-DC- DC+-G DC--G	710 540 560	not tested per UL 1449 not tested UL 1449 not tested per UL 1449
MCOV
DC+-DC- DC+-G DC--G	65 65 65	not tested per UL 1449 not tested per UL 1449 not tested per UL 1449
In (kA)	10	-
SCCR (kA)	n/a	-
Additional Data Sheet Ratings
Surge Current Rating (kA)	30	2.5
Protection Circuit	MOV (Thermally Protected)	MOV (Thermally Protected)
Leakage Current	Yes	Yes
TOV Optimized	No	No
Diagnostics	Indicator & Remote Contacts	Indicator
Environmental Rating	IP20	Manufacturer did not specify
# of Wires	3	2
Modes of Protection	Common Mode Differential Mode	Common Mode
Warranty	10-years	1-years

Determining the acceptability of an SPD for your UL equipment

(for UL 508A Control Panels and All Other UL Listed Equipment)

The UL inspector will first consider the SPD type when determining it’s acceptability for a given application or piece of equipment. This will include UL 508A as well as all other UL Listed equipment. The first level compliance is based on the UL Approval (LISTED or RECOGNIZED) of the SPD or UL SPD Type and it’s Suitable Ratings. This means that it has to meet all safety, performance, environmental and electrical system ratings of the application. If any of these criteria are not fully met, it will require a Procedure Description, a File Update and/or Additional Testing. These actions will require additional costs that may be substantial. For this reason, it is in the interest of the specifier to use UL LISTED SPD’s to eliminate any uncertainty or to make sure the UL RECOGNIZED SPD is selected at the time of UL submittal of the equipment.

Approval Considerations Table based on UL SPD Type

UL Mark	UL1449 SPD Type	Suitable Ratings	Procedure Described	File Update or Additional Testing	Notes
	1 2	Yes	No	No	The only requirement is that the SPD must match electrical and environmental ratings of the UL 508A Control Panel. A UL field inspection of the control panel with the SPD installed is required as a part of a standard follow-up service visit.
	1CA 2CA 4CA 5	Yes	Yes	Yes	Yes – All UL recognized SPD’s require a UL engineering evaluation of the SPD’s existing UL1449 E–file. This will result, at a minimum, in a cost to update the UL file and may also require testing that would result in additional costs.

10108 USA Today Way Miramar, FL 33025 USA	Contact us to develop a surge mitigation solution for your application
www.citel.us	Where to purchase Citel SPD's